Verified NACE-CIP1-001 Q&As - Pass Guarantee NACE-CIP1-001 Exam Dumps
Check the Free demo of our NACE-CIP1-001 Exam Dumps with 100 Questions
The Coating Inspector Level 1 certification program is designed to provide individuals with the necessary skills and knowledge to perform basic coating inspections. Coating Inspector Level 1 certification program is an entry-level program that is ideal for individuals who are just starting their careers in the coating inspection industry. Coating Inspector Level 1 certification program provides individuals with the necessary training and knowledge to inspect simple structures, such as pipelines and tanks.
NEW QUESTION # 46
When holiday testing is required the Inspector is always required to enforce NACE SP 0188:
- A. False
- B. True
Answer: B
NEW QUESTION # 47
Conventional spray is a good choice when:
- A. High production rates are required
- B. High viscosity coatings are being applied
- C. High transfer efficiency is required
- D. High quality finishes are required
Answer: D
NEW QUESTION # 48
Passivation can best be described as:
- A. A protective metallic oxide surface layer that slows corrosion
- B. A coating layer applied to the surface to inhibit corrosion
- C. Treating metal with a liquid inhibiter
- D. Complete elimination pf the corrosion process
Answer: A
NEW QUESTION # 49
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Galvanic Corrosion
- B. Atmospheric Corrosion
- C. Localized Corrosion
- D. General Corrosion
Answer: A
NEW QUESTION # 50
Safety Data Sheets must be carefully reviewed by:
- A. The Owner's personnel
- B. All personnel involved in the job
- C. The Inspection personnel
- D. The Application personnel
Answer: B
NEW QUESTION # 51
If inspectors identify issues of non-conformance during an inspection, they should
- A. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- B. perform additional tests secretly to ensure there are no other potential issues at the site
- C. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- D. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
Answer: D
NEW QUESTION # 52
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 53
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 1
- B. Level 2
- C. Level 4
- D. Level 3
Answer: D
NEW QUESTION # 54
SSPC SP 1 identifies the use of:
- A. A wide variety of materials
- B. Organic solvents
- C. Inorganic solvents
- D. Biodegradable detergents
Answer: A
NEW QUESTION # 55
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Purchase Professional Liability Insurance prior to job commencement
- B. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- C. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- D. Meet with the owner and explain your limitations and concerns prior accepting the assignment
Answer: C
NEW QUESTION # 56
Non Conformance Reports are completed by the Inspector:
- A. When the Inspector deems it to be a significant non-conforming item
- B. In every instance that an item does not meet the specification requirements
- C. When the Inspector and Contractor deem it to be a significant non-conforming item
- D. In accordance with the specification's definition of a non-conformance
Answer: C
NEW QUESTION # 57
The main responsibilities of the inspector are to
- A. observe and report the quality of the work performed.
- B. observe and direct the work of the contractors.
- C. direct and perform the work stated in the specification.
- D. demonstrate to the contractor how to apply the coating.
Answer: A
NEW QUESTION # 58
Polymerization is the process of:
- A. Monomers telegraphing
- B. All thermoplastic coatings
- C. All organic coatings
- D. Monomers joining together
Answer: D
NEW QUESTION # 59
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Document the problem and advise the Contractor and Owner's representative
- B. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- C. Document the problem and advise the Contractor
- D. Break the blisters to see what's inside
Answer: A
NEW QUESTION # 60
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. what materials were used.
- B. when the coating will be reapplied.
- C. what items were coated.
- D. how the item was coated.
Answer: D
NEW QUESTION # 61
NACE Level 1 Inspectors have been trained to perform:
- A. Visual inspection, Non-Destructive and Destructive testing
- B. Visual inspection only
- C. Visual inspection and Non-destructive testing
- D. All types of inspection
Answer: C
NEW QUESTION # 62
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which hand tool the Contractor selects
- B. No, because there is no real difference in the standards
- C. Yes, because the 'two standards are not equivalent
- D. It depends on which power tool the Contractor selects
Answer: B
NEW QUESTION # 63
If a Thermoset coating is heated it will:
- A. Soften when heated and return to its original hardness when cooled
- B. Harden and return to its original hardness when cooled
- C. Harden and retain its hardness when cooled
- D. Soften when heated and retain its softness when cooled
Answer: C
NEW QUESTION # 64
Which of these tests uses a syringe?
- A. Sleeve test
- B. Soluble salts meter
- C. Potassium ferricyanide
- D. Bresle patch
Answer: D
NEW QUESTION # 65
An Inspector should change position when:
- A. The Inspectors position is not the majority position
- B. Only when directed by the supervisor
- C. The Inspector is convinced by verifiable facts
- D. The Owner can save some money by the change
Answer: C
NEW QUESTION # 66
......
The Coating Inspector Level 1 certification is ideal for professionals who are involved in the application and inspection of protective coatings in various industries such as oil and gas, marine, and construction. Coating Inspector Level 1 certification program is divided into three parts, which include a written exam, a practical exam, and work experience requirements. The written exam assesses the candidate's knowledge of coating inspection techniques, while the practical exam evaluates their ability to perform coating inspections in the field. Candidates who successfully pass both exams and meet the work experience requirements are awarded the Coating Inspector Level 1 certification, which is valid for five years.
Get professional help from our NACE-CIP1-001 Dumps PDF: https://www.dumptorrent.com/NACE-CIP1-001-braindumps-torrent.html
Clear your concepts with NACE-CIP1-001 Questions Before Attempting Real exam: https://drive.google.com/open?id=1I8wj_WjeMTTj7flTzy65KE5ROkWaobym