Authentic Cisco 300-510 Exam Dumps PDF - 2024 Updated

Get Prepared for Your 300-510 Exam With Actual 253 Questions

NEW QUESTION # 50
Refer to the exhibit.

After you applied these configurations to routers R1 and R2, the two devices could not form a neighbor relationship. Which reason for the problem is the most likely?

• A. The two routers cannot authenticate with one another.
• B. The two routers have the same area ID.
• C. The two routers have the same network ID.
• D. The two routers have different IS-types.

Answer: C

Explanation:
For those asking about the password, area authentication doesn't prevent neighboring to come up because it is carried only in LSP, CSNP and PSNP messages and not in IIH messages. https://www.cisco.com/c/en/us/support/docs/ip/integrated-intermediate-system-to-intermediate-system-is-is/13792-isis-authent.html

NEW QUESTION # 51
Refer to the exhibit. Routers RA and RB are IS-IS peers configured for NSF but router RC is an IS-IS peer without NSF capability. If RA undergoes processor switchover what is the effect on the network environment?

• A. If RC is operating without the Cisco configuration option only 2 routers tear down their peering relationships and re-establish peering
• B. If RC is operating without the Cisco configuration option all three routers tear down their peering relationships and re-establish peering
• C. All peer relationships remain up and the link-state database is unchanged
• D. All peer relationships remain up, but the link-state database is rebuilt on each device

Answer: D

NEW QUESTION # 52
Refer to the exhibit.

Refer to the exhibit. This network is deployed with all connected links configured to run IS-IS. The routing protocol is enacted globally on each router, and the network engineer expects full routing Information to be shared among all routers. R5 is receiving routes from R4 but is missing routes from R1. Which action corrects the issue so that all routes are shared among the routers?

• A. Configure all routers to reside in toe area.
• B. Configure R3 as a Level 2 we.
• C. Configure R5 in the same as RI,
• D. Configure RI and RS as Level 1"Level 2

Answer: A

NEW QUESTION # 53
Drag and drop the features from the left into the order of operations for SRv6 SSH field creation and forwarding on the right.

Answer:

Explanation:

NEW QUESTION # 54
Refer to the exhibit. Which effect of this configuration is true?

• A. It sets the keepalive timer to 30 milliseconds and the hold timer to 240 milliseconds
• B. It sets the keepalive timer to 30 seconds and the hold timer to 240 seconds.
• C. It sets the hold timer to 30 milliseconds and the keepalive timer to 240 milliseconds
• D. It sets the hold timer to 30 seconds and the keepalive timer to 240 seconds

Answer: B

Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_bgp/command/irg-cr- book/bgps1.html#wp1552800140

NEW QUESTION # 55
Refer to the exhibit. Which two commands must the engineer configure for the company's PIM- PIM network to enable Auto-RP mappings to be sent over the FastEthernet0/0 interface without affecting normal operation? (Choose two)

• A. enable sparse-mode
• B. enable sparse-dense mode
• C. enable dense mode
• D. enable Auto-RP announcements
• E. enable auto-rp listener

Answer: B,E

NEW QUESTION # 56
Refer to the exhibit.

Refer to the exhibit. An engineer is troubleshooting an issue with this network and notices that prefixes from R3 are missing on the R1 routing table Due to repeated ASN when the 10 0 0 0'8 prefix from R3 arrives at R1, BGP automatically rejects it There is no prefix-list on R1 which blocks the traffic from R3 What should the engineer do to fix the problem so that BGP allows that prefix on R1?

• A. Configure R2 as a route reflector client of RI.
• B. Configure the allowas-in command on RI.
• C. Configure identical confederation ASNs on RI and R2.
• D. Configure the next-hop-self command on R2.

Answer: B

NEW QUESTION # 57
Refer to the exhibit.

P1 and PE3 Cisco IOS XR routers are directly connected and have this configuration applied. The BGP session is not coming up. Assume that there is no IP reachability problem and both routers can open tcp port 179 to each other. Which action fixes the issue?

• A. Change HMAC-MD5 to HMAC-SHA1-12
• B. Change HMAC-MD5 to MD5
• C. Change HMAC-MD5 to HMAC-SHA1-20
• D. Configure the send and accept lifetime under key 1

Answer: D

NEW QUESTION # 58
Refer to the exhibit.

Refer to the exhibit. Routers CE1 and CE2 are in AS 65530. which is multihomed for Internet access. An engineer expects inbound traffic to AS 65530 to arrive from PE1. but it is coming from PE2 instead PE1 and PE2 routers are connected with CE routers through the same bandwidth Which action must be taken to correct the problem?

• A. On router CE2, configure inbound routes from PE2 to CE2 with a local-preference value of 50 or greater.
• B. Configure router CEI to prepend the AS path to routes it receives from PE 1.
• C. Set the local-preference value on router CEI to 100 or greater
• D. On router PEI , change the origin for routes that are redistributed from CEI to CE2.

Answer: C

NEW QUESTION # 59
Refer to the exhibit.

An administrator is troubleshooting network issues on a customer's network PE1 cannot form an LDP relationship with PE2 using LDP ID 192 168.1.1. Due to this connectivity issue, the customer's routes behind both PE routers cannot be exchanged. Which action must the administrator take to correct the problem?

• A. Configure PE1 with a static route to 192 168.1.1.
• B. Create a targeted LDP session on PE2 to override the missing routing table entry on PEL
• C. Enable LDP session protection on the link that P1 uses as the next hop to PE2.
• D. Configure PE2 to automatically select its own LDP router ID with 192.168.1.1.

Answer: A

NEW QUESTION # 60
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network. Which tasks should the engineer use to solve the routing issues? Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)

Answer:

Explanation:

NEW QUESTION # 61
Refer to the exhibit.

Refer to the exhibit Reuters R2. R3, R4 and R5 all reside in the same area, with R1 in a different area R3 is overutilized and the engineer wants to reduce its CPU load The engineer configured router R4 to summarize routes that it receives from R5. but R3 is still receiving all of the R5 routes. Which action resolves the issue?

• A. Configure the summary routes on R5.
• B. Configure R3 in a new area,
• C. Configure R2 as a Level 1 router
• D. Configure R4 as a Level I-Level 2 router

Answer: B

NEW QUESTION # 62
What Is a characteristic of a segment routing mapping server?

• A. It serves multiple VRFs.
• B. It applies SID mappings from one IGP instance to another IGP instance.
• C. It must be placed in the core of the network.
• D. It must have an IGP adjacency.

Answer: D

NEW QUESTION # 63
Refer to the exhibit.

A network engineer configured routers R1 and R5 to run in IS-IS Level 1 mode and router R6 to run in IS-IS Level 2 mode. All other routers are running as Level 1 / Level 2 routers. An engineer expects traffic from R1 to R6 to pass via R2, but IS-IS routing has calculated the best path via R4. Which action corrects the problem?

• A. Change the link metric for the link from router R1 to router R2 to 1.
• B. Configure all routers as Level 1 routers.
• C. Configure all routers as Level 1 / Level 2 routers.
• D. Remove the link metric for the link from router R1 to router R2.

Answer: A

Explanation:
The default link metric for IS-IS is 10, so changing the link from R1 to R2 to 1 will change the overall metric to R6 to 9 (8+1).

NEW QUESTION # 64
Which statement about BFD on Cisco IOS XR Software is true?

• A. Cisco IOS XR Software does not support BFD multihop for IPv4.
• B. Cisco IOS XR router must use LDP to route back to the Cisco IOS router to establish the peer relationship.
• C. Cisco IOS XR router must use dynamic routing or a static route back to the Cisco IOS router to establish the peer relationship.
• D. BFD is not compatible between Cisco IOS XR and Cisco IOS Software.

Answer: C

Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r6-3/routing/configuration/ guide/b-routing-cg-asr9000-63x/b-routing-cg-asr9000-63x_chapter_0100.html

NEW QUESTION # 65
Refer to the exhibit. A network operator is configuring BGP PIC on CE1 on already established neighborships with PE1 and PE2 inside the fully converged MPLS network. Which element needs to be implemented to make this feature function effectively?

• A. The operator must ensure that all prefixes have the same next-hop from PE1 and PE2 for BGP PIC
• B. A reserved BGP community of 1:10 must be used to denote the PIC feature set to the routing protocol
• C. BGP import export policies must be applied on all devices for the routes needing BGP for PIC
• D. Bidirectional Forwarding Detection must be applied to the upstream facing BGP interfaces

Answer: D

NEW QUESTION # 66
Refer to the exhibit.

Customer traffic from the branch site to the hub is experiencing packet drops. The engineer verified that:
Customer traffic from the hub is able to reach the branch site.
The connection between PE1 and PE2 is working normally.
Routers P1 and P2 are able to ping devices on the hub site.
Which action resolves the issue?

• A. Redistribute the CE1 OSPF routes in the PE1 VRF.
• B. Advertise the VPNv4 routes of the hub in CE1.
• C. Redistribute the CE2 OSPF routes in the PE2 VRF.
• D. Advertise the VPNv4 routes of the branch site in CE2.

Answer: A

NEW QUESTION # 67
Refer to the exhibit.



Refer to the exhibit. Multicast traffic destined from T1 and T2 routers to RP routers works well. A network engineer observes problems with multicast traffic flows between Site-A and Site-B. Site-A users fail to receive multicast stream on Site-B via RPTY site, while Site-B users fail to receive multicast stream on Site-Avia RPTZ site. Which action must be implemented to resolve the issues?

• A. Allow the OSPF and MSDP packets on the firewall.
• B. Configure Site-A and Site-B in 10.80.14804
• C. Establish MDSP peering with interface IP subnet.
• D. Configure direct OSPF peering between Site-A and Ste-B

Answer: A

NEW QUESTION # 68
Refer to the exhibit. A network engineer applied configuration on R5 to summarize all OSPF routes, but R4 is still receiving specific routes from R5. The engineer has confirmed that both R5 and R4 routers are configured with correct summarization configuration but R5 Is not sending the summary routes. What action must the engineer take to fix the problem?

• A. Move R4 and R5 in separate areas as now they maintain the same link-state database
• B. Remove summarization configuration on R5 and configure it on R4
• C. Clear link-state database on both R4 and R5 routers for summarization to work
• D. Configure a sham link between R4 and R5 to support summarization within Area 2

Answer: A

NEW QUESTION # 69
Refer to the exhibit.

A network operator is working to deploy a Unified BGP design and allow it to be available only in selected markets and services in the future. The label allocation is not functioning as desired. Which action will fix the issue?

• A. Reconfigure the route-policy ALL_LABELS to pass.
• B. Remove the route policy and only configure "allocate-label".
• C. Reconfigure the route-policy ALL_LABELS to match all after the drop.
• D. Remove the allocate-labels command.

Answer: A

NEW QUESTION # 70
Refer to the exhibit.

Routers R1, R2. R3, and R4 have been configured to run OSPF. and router R5 is running EIGRP Traffic from R1 to R5 is expected to pass via R4. but OSPF routing has calculated the best path via R3. Which action corrects the problem?

• A. Configure R3 to use metric-type 1 with a higher metric than R4.
• B. Change the metric-type value on R3 to 2.
• C. Reconfigure R1 in Area 0.
• D. Configure R1 with a static route to the R5 networks and set R5 as the next hop.

Answer: B

NEW QUESTION # 71
Refer to the exhibit.

R3 is:
failing to accept multicast RP information from Domain-A
advertising MSDP SA messages to R1 and R4
receiving SA messages only from R4
Which command must the engineer implement to resolve the issue?

• A. R3# ip msdp sa-filter in 192.168.3.1
• B. R3# ip msdp sa-filter out 192.168.1.1
• C. R3# no ip msap sa-filter in 192.168.1.1
• D. R3# no ip msdp peer 192.168.1.1

Answer: C

NEW QUESTION # 72
......

Accurate & Verified New 300-510 Answers As Experienced in the Actual Test!: https://www.dumptorrent.com/300-510-braindumps-torrent.html

Valid 300-510 Test Answers Full-length Practice Certification Exams: https://drive.google.com/open?id=1TNPywSY3gd2ZhPy_AxDcMDO1UurUzvMM